Rle TH140D Manual do Utilizador descarregar pdf (Página 1)

VERIS INDUSTRIES

™

environmental SenSorS

inStallation GUiDe

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Wall Mount Humidity Sensor

Installer’s Speciﬁcations

HS Element Digitally proﬁled thin-ﬁlm capacitive (32 bit mathematics)

U.S. Patent 5,844,138

Accuracy at 25°C from 10-80% RH* 2%, 3%, or 5% models;

±1% at 12-60% RH in voltage output mode;

±1% at 12-60% RH in mA output mode with temp. transmitter;

±1% at 20-40% RH in mA output mode

(Multi-point calibration, NIST traceable)

Reset Rate** 24 hours

Stability ±1% @ 20°C (68°F) annually, for two years

Operating Humidity Range 0 to 100% RH (non-condensing)

Hysteresis 1.5% typical

Linearity Included in Accuracy spec.

Temperature Coeﬃcient ±0.1% RH/°C above or below 25°C (typical)

Analog Output 4-20mA version: 2-wire, polarity insensitive, (clipped and capped)

0-5V/0-10V versions: 3-wire, observe polarity

Scaling 0-100% RH

Operating Temperature Range 10° to 35°C (50° to 95°F)

Input Power*** 4-20mA version: loop powered 12-30VDC only, 30mA max.

0-5V/0-10V versions: 12-30VDC/24VAC, 15mA max.

Optional Temperature Transmitter Output Digital, 4-20mA, (clipped and capped) or

0-5V/0-10V output; accuracy ±0.5°C (±1°F) typical

EMC Conformance – CE Option EN 50081-1, EN 50082-1, EN 61000-4-4, EN 61000-4-5, EN

61000-4-3, ENV 50204, EN 61000-4-6

*Speciﬁed accuracy with 24VDC supplied power with rising humidity. RTD/Thermistors are not

compensated for internal heating of product.

**Reset Rate is the time required to recover to 50% RH after exposure to 90% RH for 24 hours.

***One side of transformer secondary is connected to signal common, so an Isolation transformer

or dedicated power supply may be required.

Shielded cabling is required for conformance to EMC standards. Technical information is available

from factory upon request or is available on our website: www.veris.com

HWL SerieS HWL SerieS

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• Read and understand the instructions before installing

this product.

• Turn oﬀ all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

Available

Dimensions

quick install

Select a mounting location away from ventilation sources. The sensor should be 1.

mounted on a vertical wall, about 4 ½ feet above the ﬂoor.

Aﬃx the backplate to the wall.2.

Wire the device. Refer to wiring diagram.3.

Install Cover. 4.

3.5"

(89 mm)

4.8"

(122 mm)

1.2"

(30 mm)

1 2 3

Resumo do Conteúdo

Página 1 - HWL SerieS HWL SerieS

Página 2 - ProDuct iDentification

Página 3 - HWl SerieS

Comentários a estes Manuais

Sem comentários

Rle TH140D Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Sensores Rle TH140D. RLE TH140D User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Rle TH140D Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Sensores Rle TH140D. RLE TH140D User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Rle TH140D